Watch repair

For firm gluing of watch glasses, gemstones, and others. The 2-component watch glass glue is ideal for bonds that must meet the highest standards. The adhesive is resistant to chemicals, such as dilute acids and alkalis, petrol, many solvents, and moisture. Benefits of the 2C glue: It dries clear and distinguishes itself - in comparison with fast-curing 2-component epoxy resins - by proper processing with very high resistance to yellowing (with minimal intrinsic colour). Suitable for bonding glass, ceramics, wood, stone, concrete, marble, metals, thermosets, many hard plastics, glass fibre reinforced plastics, and Styrofoam®. Not suitable for soft plastics, PE, PP, rubber, nylon, and for bonds that are subject to bending stress. Because of its low viscosity, the 2-component watch glass glue is only suitable for bonding in which the adhesive composition cannot flow away during curing. Contents: 100g resin C and 40 g hardener V20L

Grit ??, length 115 mm , dia. 10mm

For lifting the plastic glasses from waterproof one-piece watch glasses. First, the crown and shaft are removed with the supplied crown puller. The end piece that fits the tube is placed on the pump. Air is pumped into the watch with the pump until a pressure is generated that blasts the glass up and out of the seat without damaging it. (First pull out the crown as you do when changing the time. The stem consists of 2 parts that are connected and can be pulled out (with the special key provided). Remove the half stem and the crown with the key .Using the pump: Pull out the air pump hose completely Press the plastic tip of the air pump against the watch case (or case hose) Hold the case while placing your thumb lightly on the glass and press firmly the pump to pump the glass out of the watch.)

• Precision machined from high quality, matt superior stainless steel • Shapes in set: SS - MM - 7 - 3C - 5 - 3 - 1 - AA • With protective caps • With SELVA logo • In plastic bag • Total weight approx. 139g

Super practical range with six work or sorting trays: • Stackable • Transparent • Contents: 6 pieces, each with a lid • Interior division: 4 smaller compartments, 1 large, round compartment - ideal for small watch movements up to approx. Ø 46mm • Outside Ø 76mm • Height approx. 17mm

3-piece set RX for Oyster, Jubilee and Standard style straps Total weight approx. 3.8kg

Band pin remover with springs of different strength to vary the impact intensity for easily removable to very tight band pins. Includes: - 3 springs in different strengths - 2 broaches with pin 0.8 mm

USTANOL from BALLISTOL - the precision engineering oil with extremely high creeping activity! Has proven itself in every workshop with great properties for years: • Low viscosity • Extremely high creeping activity • Cleans, lubricates and protects all metal parts • Infiltrates and displaces water • Rust protection • Rust remover • Free of PTFE and silicone • Content: 200ml • MADE IN GERMANY Typical fields of application: • Precision mechanical devices, measuring tools, clocks and locks • Cutting and milling work, threads and fits Ideal for the care, lubrication and preservation of fine mechanical devices, precision instruments, machines and production systems, tools and Workshop machines, all metal parts. Also prevents brass and copper from tarnishing. BENEFITS: • Thin, economical neural oil • Enormously high creeping ability • Strongly adheres to metals • Cleans, lubricates, protects and removes unsuitable oils, gums and other residues • Resistant to aging • Infiltrates and displaces water • Suitable as a contact oil and rust remover • Does not resinify, silicone, PTFE and acid free • Free from animal oils Operating temperature range from -50 ° C to approx. 150 ° C Technical specifications: Density g / cm3 at 20 ° C: approx. 0.84 Viscosity mm2 / s at 20 ° C: 4.80 Viscosity mm2 / s at 50 ° C: 2.90 Drop point: -51 ° C Surface tension mN / m at 20 ° C: 26.50 Creep capacity on sheet steel after 60 minutes: 4.0 Ustanol precision engineering oil is a specialist among technical oils. It is a pH-neutral oil with an extremely low surface tension and an equally low viscosity. This makes Ustanol particularly easy to creep and automatically penetrates into the smallest spaces. Ustanol creep oil is resistant to aging and does not resinify. It reliably creeps under water on metals and, thanks to its low surface tension and enormous ability to creep, offers reliable rust protection even in the last corner. Hazard warning: Highly flammable liquid and vapor. Can be fatal if swallowed and enters airways. Causes skin irritation. May cause respiratory irritation. May cause drowsiness and dizziness. Toxic to aquatic life with long lasting effects. Additional information aerosol packaging: Extremely flammable aerosol. Pressurized container: May burst if heated.

Ideal for the workplace Ideal for keeping hammers, ring sticks, pliers and much more in order and ready to hand. A total of nine holes as well as a practical magnetic surface on the side of the stand, to which e.g. pliers, files etc. can be attached. Attention: The stand is delivered in red (MDF wood) Dimensions: width 45cm x depth 17cm x height 17cm

For almost all wristwatches High-quality special tools and an assortment of the most important spare parts are optimally put together. Box approx. 16 x 30 cm. Scope of delivery: Case opener with adjustable steel grippers, case opener blade, plastic tweezers, screwdrivers 1, 1.2 and 1.6 mm with replacement blades, spring bar assortment 8-24 mm, fine tweezers AA, spring bar cutlery, magnifying glass: 2.5 times

Plastic, with flat, smooth tips. Top with metal insert for opening battery compartments.

Analogue display with red/green limit mark. Measuring ranges up to: - 1.5V for silver oxide batteries (low/high drain) - 3.0V for lithium batteries As an additional feature, there is an output pulse control for analogue quartz watches with unopened watch case. The output pulse is displayed by an LED. The tester is operated with a battery (lithium CR2430 included).

The Bergeon universal screw press made of anodized aluminum is ideal for setting watch glasses and pressed case backs. Of course, SWISS MADE in proven Bergeon quality and compatible with many Bergeon inserts. Benefits: • Made of anodized aluminum with non-slip base • Linear spindle with anti-rotation • Spoked handwheel Ø 100 mm • Spindle and insert holder with M6 thread • Working height for watches up to 45 mm high • Compatible with many Bergeon inserts • Optionally further insert holders available (our references 219209 (height 5mm) or 219210 (height 28mm) Scope of delivery: • Screw press • M6 mounting adapter with a height of 21mm (also available individually under reference 203243)

Bergeon press-fit bearings brass B27, hole Ø 4.00 outer Ø 6.50 height 1.50 mm, capacity 10.00 Unit

Bergeon press-fit bearings range brass 5488, bore Ø 0.35 outside Ø 2.00 height 1.20 mm, capacity 450.00 units

BERGEON rubber ball case opener A friction ball that opens the back of most screw-off style watch backs. This squishy ball is slightly tacky and creates a large contact area that allows you to open the back easily. Guaranteed to not scratch or leave a mark on your watch, this tool is great when you want to open a back without the hassle of using traditional case opening tools. • Allows you to get an excellent grip • Rubber friction ball • Size: Ø 67 mm

Winding tool from Bergeon in Swiss Made quality Universal tool for mounting anodized aluminum wristwatches with elastomer insert. The Bergeon tool is an ideal tool for mounting mechanical watches after repair. Ideal: The soft elastomer insert adapts to various crown shapes and ensures very good adhesion to the crown. Recording Ø: 2.5 - 10.0 mm Weight: 35 g Manufacturer: Bergeon Catalog no. 31409

SWISS MADE With aluminium handle. Length: 115 mm.

- Bestfit for Model 1675/0, 16750 - RLX Pepsi - Print: 2-22 - Black - White - European Quality - Diameter Outside/ Inside: ca. Ø 37,7mm/ 30,1mm

- Bestfit for Model 1675/0, 16750 - RLX Pepsi - Print: 2-22 - BLue-Red - European Quality - Diameter Outside/ Inside: ca. Ø 37,7mm/ 30,1mm

- Best fit for 16610 - RLX SUB - Ceramic - Print 10-50 - Black - white - European Quality - Diameters ca. Ø 37,7mm/ 30,6mm

for blowing out, draining and dusting clockworks, instruments, small gears, relays etc. With one-way valve. Even if the term "rubber blower" seems to have prevailed (and we will also use it as a title for better finding in the online shop), this term is not correct. The material of the dust blower is by no means rubber. The dust blower consists of a phthalate-free soft PVC of medical quality, this material is protected and is called Sarolit® - no rubber. The blow-out nozzle itself is a component made of HD-PE, also of medical quality. Both components are manufactured and assembled in Germany. The weight of the product H3 is 40g, the blow nozzle 0.4g.

Fits 4229071.

Opening and closing of bezel settings / sockets in hard-to-reach places. In the watchmaker's workshop, the polishing steel is also used to polish broken edges on steel parts. Depending on the desired width of the polishing edge (bevel), more or less fine sanding is carried out before polishing. Length 145mm Wooden handle curved design