Aquarius 80 N

In AQUARIUS welding and soldering devices, the gas is in the device is generated electrochemically from water and electricity (electrolysis). The Aquarius devices are equipped with only a relatively small electrolyte reservoir. The electrolyte will be consumed after about 1 to 3 years and must then be replaced. In order to maintain the function of the device, it is merely necessary to maintain the correct level of the electrolyte by adding distilled water. Apart from that these devices require hardly any further maintenance in everyday use. The devices generate only as much gas as is consumed at a time. The highly pure gas prevents heavy tarnishing of the jewellery being soldered. Devices with different gas outputs from 50 to 130 litres per hour are available for various areas of application. The flame temperature is up to 3200 °C, fore example, for platinum processing where no flux is used. The flame is from virtually invisible to pale blue and can be coloured green by addition of methanol and at the same time lowered to about 2400 °C. The flame can be easily dosed and used precisely to the point by the settings on the burner and the choice of nozzle size. The time required to melt a metal in soldering/welding is, however, not only determined by the temperature of the flame, but also by the rate at which the flame energy is supplied to the workpiece. In this manner, even delicate jewellery can be soldered quickly and gently, without heating the entire part. Technical equipment of all Aquarius devices offered: - Gas purification/condensate separation with filter gravel - Safety pressure limiter with audible signal - Thermostat switch for temperature monitoring - 2 flame arrestors - Integrated booster container for flux-methanol mixture - 4 years warranty Accessories for 1 workstation included with all Aquarius devices: 1 burner handpiece with fine control valve and hose 1 burner stand/burner suspension bracket each 4 burner nozzles, assorted (no. 18, 20, 22, and 26) 2 level floats 2 hoppers 1 cleaning syringe 1 electrolyte filling 1 litre of flux -For fine, small, and large soldering work in the goldsmith's and watchmaker's workshop and in the dental laboratory. Technical Specifications: - For 1-3 workstations - Reactor contents 1.35 litre electrolyte - Steplessly variable power adjustment for adjusting the gas output to the job - Amperemeter for performance monitoring 230 V / 50 Hz, 460 Watts.

In AQUARIUS welding and soldering devices, the gas is in the device is generated electrochemically from water and electricity (electrolysis). The Aquarius devices are equipped with only a relatively small electrolyte reservoir. The electrolyte will be consumed after about 1 to 3 years and must then be replaced. In order to maintain the function of the device, it is merely necessary to maintain the correct level of the electrolyte by adding distilled water. Apart from that these devices require hardly any further maintenance in everyday use. The devices generate only as much gas as is consumed at a time. The highly pure gas prevents heavy tarnishing of the jewellery being soldered. Devices with different gas outputs from 50 to 130 litres per hour are available for various areas of application. The flame temperature is up to 3200 °C, fore example, for platinum processing where no flux is used. The flame is from virtually invisible to pale blue and can be coloured green by addition of methanol and at the same time lowered to about 2400 °C. The flame can be easily dosed and used precisely to the point by the settings on the burner and the choice of nozzle size. The time required to melt a metal in soldering/welding is, however, not only determined by the temperature of the flame, but also by the rate at which the flame energy is supplied to the workpiece. In this manner, even delicate jewellery can be soldered quickly and gently, without heating the entire part. Technical equipment of all Aquarius devices offered: - Gas purification/condensate separation with filter gravel - Safety pressure limiter with audible signal - Thermostat switch for temperature monitoring - 2 flame arrestors - Integrated booster container for flux-methanol mixture - 4 years warranty Accessories for 1 workstation included with all Aquarius devices: 1 burner handpiece with fine control valve and hose 1 burner stand/burner suspension bracket each 4 burner nozzles, assorted (no. 17, 19, 21, and 26) 2 level floats 2 hoppers 1 cleaning syringe 1 electrolyte filling 1 litre of flux - For fine, small, and large soldering work in the goldsmith's and watchmaker's workshop and in the dental laboratory as well as for industrial use. Technical Specifications: - For 1-3 workstations - Reactor contents 2.25 litre electrolyte - Steplessly variable power adjustment for adjusting the gas output to the job - Amperemeter for performance monitoring - Additional burner handpiece and burner stand for platinum processing with external drying container 230 V / 50 Hz, 572 Watts.

In AQUARIUS welding and soldering devices, the gas is in the device is generated electrochemically from water and electricity (electrolysis). The Aquarius devices are equipped with only a relatively small electrolyte reservoir. The electrolyte will be consumed after about 1 to 3 years and must then be replaced. In order to maintain the function of the device, it is merely necessary to maintain the correct level of the electrolyte by adding distilled water. Apart from that these devices require hardly any further maintenance in everyday use. The devices generate only as much gas as is consumed at a time. The highly pure gas prevents heavy tarnishing of the jewellery being soldered. Devices with different gas outputs from 50 to 130 litres per hour are available for various areas of application. The flame temperature is up to 3200 °C, fore example, for platinum processing where no flux is used. The flame is from virtually invisible to pale blue and can be coloured green by addition of methanol and at the same time lowered to about 2400 °C. The flame can be easily dosed and used precisely to the point by the settings on the burner and the choice of nozzle size. The time required to melt a metal in soldering/welding is, however, not only determined by the temperature of the flame, but also by the rate at which the flame energy is supplied to the workpiece. In this manner, even delicate jewellery can be soldered quickly and gently, without heating the entire part. Technical equipment of all Aquarius devices offered: - Gas purification/condensate separation with filter gravel - Safety pressure limiter with audible signal - Thermostat switch for temperature monitoring - 2 flame arrestors - Integrated booster container for flux-methanol mixture - 4 years warranty Accessories for 1 workstation included with all Aquarius devices: 1 burner handpiece with fine control valve and hose 1 burner stand/burner suspension bracket each 4 burner nozzles, assorted (no. 19, 20, 21, and 26) 2 level floats 2 hoppers 1 cleaning syringe 1 electrolyte filling 1 litre of flux For fine, small soldering work in the goldsmith's and watchmaker's workshop and in the dental laboratory. Technical Specifications: For 1 workstation Reactor contents 0.8 litre electrolyte 230 V / 50 Hz, 250 Watts.