-
All Categories
-
Clock Movements
-
DUGENA Quartz Movements
-
Radio controlled clock movements
-
Quartz movements
-
Watch movements
-
Plug-in clockwork
-
Spring Movements
-
Quartz pendulum movements
-
Clock movements with chains
-
Pairs of hands, movement
-
Pairs of hands, form
-
Dials and numeral circlets
-
Suspension Springs
-
Kieninger movement-kits
-
Pendulum springs
-
Clock chains
-
Equipment and accessories
-
Rotary Pendulum Drive
-
Wooden ornaments
-
Chain hoist movement
-
Small parts
-
Clock chains
-
Watch equipment
-
Spare parts for Rolex
-
Cuckoo Movements
-
Mechanic movements for tableclocks
-
Metal ornaments
-
Music boxes
-
Quartz movement with swing
-
Clock pendulum
-
Cable pull movement
-
Second hands
-
Grandfather's clock movements
-
Synchronous movement
-
Pocket watch hands
-
Clock plate
-
Numeral set
-
Tension springs
-
DUGENA Quartz Movements
-
Watchmaker Tool & Workshop Need
-
Clocks and watches
-
Crafting and designing
-
Batteries
-
Jewelry parts
-
Nose piercing
-
Watch spare parts
-
Clock parts
-
After brand and calibre
-
Press-fit bearings
-
Pulley wheels
-
Cabinet fittings/accessories
-
Body trim
-
Weights/accessories
-
Glass bells
-
Bells/accessories
-
Chime rods/Gong springs
- Clock key
-
Hammers/accessories
-
Chains/ropes/strings/accessories
-
Cuckoo pipes/Accessories
-
Pendulum/accessories
-
Suspension springs
-
Raw shoots
-
Screws/nuts
-
Swiss anchor escapements
-
Pawl springs
-
Sperraeder
-
Drivers
-
Watch stand
-
Balance shaft after U no.
-
Washers
-
Cotter pins
-
Hand/accessories
-
Central screw
-
Dials/accessories
-
Other Accessories
-
After brand and calibre
-
Watch glasses
-
Watch movements by brands
-
Watch Straps and accessories
-
Wristwatches and pocket watches
-
Alarm clocks and large clocks
-
Tools/supplies
-
3Dmensionals
-
Weather instruments
-
Craft & creative
-
Expert knowledge & literature
-
Household, security, outdoor
-
Special items
-
Catalogues
-
Clock Movements
Product number:
334735
Product information "Clock key, standard version, steel, long shaft, square inside: 3.75"
For table, wall and grandfather clocks.
INFO
The classic key sizes No. 00 to 15 are only familiar to watchmakers.
The dimensions, according to which winding keys are also defined, refer to the winding square of the movement. The winding square is measured (with the caliper!), the result is rounded up to 0.25 mm and then the key is selected. The key is delivered exactly fitting with the correct plus tolerance (nominal size plus approx. 0.1 mm).
In older watches, where the winding square is conical, measurements are not taken at the front, "thin" end, but a little deeper towards the inner end of the square. The measurement result is rounded up to 0.25 mm and then the key is selected.
If a square is not exactly square, but has a rectangular deviation in the cross-section, determine the dimension of the larger edge length.
Corrupted elevator square is often filed down in the course of a repair. This, or if a tension spring has been replaced by an excessively strong one, can result in extraordinary loads on the winding key, which can lead to damage or even bursting. The same applies if a key was chosen too large or the longitudinal edges of the elevator square are worn and rounded. In such cases, a guarantee that is limited to the replacement of the key is excluded.
Note: If you measure the square hole of a key, please do not measure over the center of the hole, but between two opposite corners. The reason: The cross-section of the hole is not purely square, but rather a round hole that was re-punched with a "broach". Since the diameter of the hole is slightly larger than the actual "wrench size", an incorrectly applied measurement will result in too large a square dimension.
INFO
The classic key sizes No. 00 to 15 are only familiar to watchmakers.
The dimensions, according to which winding keys are also defined, refer to the winding square of the movement. The winding square is measured (with the caliper!), the result is rounded up to 0.25 mm and then the key is selected. The key is delivered exactly fitting with the correct plus tolerance (nominal size plus approx. 0.1 mm).
In older watches, where the winding square is conical, measurements are not taken at the front, "thin" end, but a little deeper towards the inner end of the square. The measurement result is rounded up to 0.25 mm and then the key is selected.
If a square is not exactly square, but has a rectangular deviation in the cross-section, determine the dimension of the larger edge length.
Corrupted elevator square is often filed down in the course of a repair. This, or if a tension spring has been replaced by an excessively strong one, can result in extraordinary loads on the winding key, which can lead to damage or even bursting. The same applies if a key was chosen too large or the longitudinal edges of the elevator square are worn and rounded. In such cases, a guarantee that is limited to the replacement of the key is excluded.
Note: If you measure the square hole of a key, please do not measure over the center of the hole, but between two opposite corners. The reason: The cross-section of the hole is not purely square, but rather a round hole that was re-punched with a "broach". Since the diameter of the hole is slightly larger than the actual "wrench size", an incorrectly applied measurement will result in too large a square dimension.
| Application: | 3,75 |
|---|---|
| Article name: | Clock key |
| Interior dimension Ø mm: | 3.75 |
| Manufacturer name: | 6 |
| Material: | Messing, verchromt |
| Processing mode: | verchromt |
| Special feature: | long shaft |